Fashion DC 5V 2.1A Mobile Power Diy Board 4.2V ChargeDischargeboostbattery Protectionindicator Module 3.7V Lithium TP5000 TP5100

BBS:http://forum.mhetlive.com/ Product Features Charging voltage: DC 4.5V-5.5V (recommended DC 5V) Charging current : 0-2.1A Charging quiescent current: 100uA Full voltage: 4.2V+-1%. Discharge current: 0-3.5A; Discharge quiescent current: 50uA Discharge efficiency: 96% maximum Output voltage: 5V Output current: 0-2.1A; Ambient temperature: -20° to +85° Module with lithium battery protection function (for lithium battery without protection, with protection board) Overcurrent protection (OCP) Overvoltage protection (OVP) Short circuit protection (SCP) Over temperature protection (OTP) Charge and discharge power level 4 interval indication Pin definition

TP5100 is a double switch buck 8.4V, single cell 4. 2V lithium battery charge management . Its ultra-compact QFN16 package and simple external circuit, making TP5100 ideal for portable equipment so large current charging management applications.Meanwhile, TP5100 built-in input overcurrent, undervoltage protection, over temperature protection, short circuit protection, battery temperature monitoring, reverse battery protection. TP5100 have 5V-18V wide input voltage, dual battery trickle charge into pre-charge, constant current, constant voltage three phase, pre-charge current trickle charge current through an external resistor adjustment, the maximum charge current up to 2A. TP5100 with a frequency of 400kHz switching mode makes it poible to use a smaller outer Suo device and the large current charging still maintain a smaller amount of heat. TP51OO built-in power PMOSFET, anti-intrusion circuit, so no anti-intrusion protection and other external Schottky diode. Features: - Double 8.4v / 4.2v lithium rechargeable single - Programmable charge current. 0. 1A-2A - Programmable steady precharge current 10% -100%. - Wide operating voltage, maximum reachV - Red and green LED charge status indicator - temperature protection, overcurrent protection, undervoltage protection - Battery temperature protection, reverse battery shutdown, short circuit protection - Switching frequency 400Khz, usable inductance 20uH and more - PWR_ON Power battery for switching control Maximum Ratings: - Static input supply voltage (VlN): 20V - BAI: -8.4V-20V - BAT Short-Circuit Duration: Continuous - Operating envment Temperature range: -40 ° -85 ° - Storage temperature range: -65 ° - 125 ° Application: - Portable equipment, various chargers - Smartphone, PDA, mobile cellular telephone - MP4, MP5 players, tablets - HM - Power Tools - Walkie-talkie Default shipping settings: 4.2V 2A. The board has with LED, and LED's external reserve position. Size: 25 * 17 * 5mm ultra-small size Input voltage: 5-18V DC power supply Charge status: full and unloaded blue lights, charging red.

TP5000 Product : TP5000 lithium ion battery lithium phosphate battery 1A current 4.2/3.6V Function: Charge lithium battery and lithium phosphate battery. Full of self-stop. Red and green double lights indicate. Usage: TP4056 4057 charging board usage is the same. 1. The lithium battery only needs to be connected to the 5V power supply, and the output B+B- can be connected to the battery. The red light is on during charging, and the battery is fully charged. The green light is on ar charging. 2, for lithium phosphate battery 3.6V, just soldering to open the tin point between the two pads. The power battery connection method is unchanged as described above. If you need to change the charge to a 4.2V lithium battery, use the pad to solder it back. Product introduction: Advantages: Switching buck mode, the efficiency is higher than the linear charging circuit, and the heat is much smaller. The charging current is 1A and is maintained at 1A during constant current charging. No additional heat diipation is required, which reduces the effect of heat on the charging current. Reduce charging time. An optional lithium ion lithium polymer battery or lithium phosphate battery can be changed with only one jumper. parameter: Input: 4.5-9V Output voltage: 4.2V/3.6V plus or minus 1% (board default lithium-ion battery 4.2V) Output current: default 1A Ar the efficiency test, it will be described in detail. If the buyer tests the efficiency, it is not recommended to test the battery terminal voltage. Please skip the Rs sampling 0.1 resistance test. In the test, the input power is close to the circuit board, and reducing the length of the connection will have an efficiency test. Impact, it is recommended to increase the capacitance test at the input. The voltage and current test suests that the current meter with string accuracy is not recommended to read the power supply digital display directly. The current test can be directly connected in series with the positive electrode of the battery. It is only neceary to ensure that the battery is tested below the 3.9V using a large-scale ammeter. Features: The whole version uses precious cermet capacitors, X7R temperature characteristics, performance + safety + stability far exceeds tantalum capacitors! Copper strip 5A high current small volume inductance, fully closed magnetic low lo and low interference! Single-sided machine mounting, overall 4 mm ultra-thin, small area, good heat diipation, easy to install and paste heat sink on the back Based on DC-DC buck, the efficiency is much higher than that of a linear charging circuit, and the heat is much smaller. The charging current is 1A, but the input current is only about 0.7A. Optional lithium phosphate battery or regular lithium ion/lithium polymer battery, only one jumper can be set Small size, 1 hair coin size, 1A charging without additional heat With overheat protection, overheating will automatically reduce the current to prevent burnout Full-page high-precision resistor, the most stable temperature characteristic of full-size 1210 precious metal multilayer ceramic capacitor X7R Fully self-stop, two-color charge status indicator Input: 4.5-9V (recommended not to exceed 7V) Output voltage: 4.2V/3.6V plus or minus 1% jumper selection Output current: default 1A can be customized 0.5-2A, greater than 1.5A need to add heat 4 terminal blocks, 2 inputs, 2 batteries, and soldering position with in-line LED Instructions: A red, green or red-green LED is included with the circuit. You need to solder it to the circuit yourself. As shown in the baby figure, in the middle of the longest foot, the middle and long legs are close to the , and the shortest foot is close to the outside. The power supply is terminated with a 4.5-7V power supply. The current is greater than the charging current. At this time, the green light is on. The battery is terminated with a lithium battery or a lithium phosphate battery. If the battery needs to be charged, it will turn red. If you need to adjust the current, modify the current you need at the current sampling resistor. Sampling voltage 0.1V, current = 0.1 / resistance value The circuit has been soldered with a 0.1 resistor and there is a vacancy The vacancy is soldered with a 0.2 resistor and the current is set to 1.5A. The vacancy is soldered with a 0.1 resistor and the current is set to 2A. Remove the R100 (0.1), solder a 0.2 resistor, set the current to 0.5A It is recommended to install a heat sink with a charging current greater than 1A. If you need to charge a normal lithium battery (3.6 or 3.7V. 4.2V cutoff voltage), please click on the solder joint on the board F. If you need lithium phosphate battery (3.2V. Cutoff voltage 3.6V), please remove the solder on the standard F solder joint.

About shipping
Shipping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days ar buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.