0-330V Smart-Fit Manual Adjustment Voltage TV LED Backlight Tester Current Adjustable Constant Current Board LED Lamp Bead

Multurpose Tester for LED TV Backlight & Constant Current Driver Board Model: TD3H Vin: AC85-265V

Vout: DC 0-330V (Automatic + Adjustable) Accuracy: ＜(± 0.5 ± 1% Vout)V Iout: 0-150mA(Automatic + Adjustable) Constant Current Board Testing Current: 0-999mA Accuracy: ＜(±2 ±1% Iout) mA Pinput: 50VA(MAX) Temperature: -20℃ - +40℃ Product introduction: Real-time testing voltage and current of constant current drive board. 1 . Testing LED strs , LED panels , single LED bead , COB ighting sources and so on. 2 . Testing backlight of LED TV , displays , computers and so on . 3 . Compatible with all the LED strs ( high voltage or low voltage ). 4 . Manual adjusting the range of testing voltage( 20-330V / DC ) and current ( 20-150mA ).Adjusting voltage at open circuit ( without loads ) and adjusting current with loads or contact probes together. 5 . No burn out when testing sinale LED bead with wrong polarity ( Set voltage around to 20V and the current  switch to 1mA). 6 . Testing voltage parameter of various of electronic components. 7 . Testing LED light on vehicle. Testing Methods: Default factory setting : Output Voltage 330V , Output Current 30mA . You can testing the backlight of TV with any size at this default settings. 1 . Self-testing: Plug in , turn the power switch on . The voltage is around 330V , current is 0 : Contact the   probes together , voltage changes to 0 and current changes to around 50mA , then testing can be started

2 . In testing: Voltage = '0' , SHORT CIRCUIT Voltage = '330V' , OPEN CIRCUIT.

3 . Testing single LED bead ( Set voltage around to 20V and the current switch to 1mA ) . 3.1. With right polarity: the voltage shows on the tester of a normal LED bead is about 80% of the rated voltage, for example,the operating voltage of the LED bead is 2.4V if its rated voltage is 3V; 3.2. With wrong polarity: Voltage display the open circuit voltage.

4. Testing LED strs: Set the voltage to around 200V,change the current if need adjust brightne. Test method without disaembling the screen. Cut off the power of TV,Unplug the interface sockets of the constant current plate and light bar, Insert the Red and Black pens of the tester into the anode and cathode of the interface of the LED light bar. 1. Multle LED strs Testing the voltage of each strs and record them.Compare the voltage of each strs , it is normal if the differences < 2V or < 3% 2. Single LED str 2.1. The LED str is not on ( need remove the screen to repair ): Voltage = 0, SHORT CIRCUIT. Voltage ≥300V, OPEN CIRCUIT. 2.2. The LED str is on ( need the testing references of constant current driver board to determine the backlight is normal or not ). Test method of Constant Current Driver Board Testing situation : the LED str of backlight is on with the tester ,but it does not work with the constant current board. 1. Cut off the power of TV, unplug the interface sockets of the constant current plate and light bar. 2. Connect the constant current board with the tester using the cables in the kits on right polarity. 3. Insert the Red and Black pens of the tester into the anode and cathode of the interface of the LED light bar . 4. Turn the power of TV on. 5. Testing voltage > 30V, Current >30mA and keep stable,and the LED str working normal, then the Constant current board is normal. Introductions of the additional function Voltage Test of Electrolytic Capacitor: Connect the black pen with the cathode of the electrolytic capacitor and the red pen with the anode. The voltage value displayed in the will rise fast at the beginning. When reaching a certain point, the rising velocity will slow noticeably. At this time the voltage value displayed is the actual withstand voltage of the tested electrolytic capacitor. ( The capacitors are qualified if the actual voltage value is higher than the indicated voltage value). Notice: Avoid to break the capacitor, the testing time should not be too long. 1. Set the voltage around 20V and the current to ImA when testing the voltage references of diodes, triodes, MOS tube and IC . 2. Set the Voltage around 330V and the current to 1mA when testing the breakdown voltage of capacitors,stabilivolts,piezoresistors and TVs. WARRANTY 1. This product is guaranteed up to one year from purchase, power cord and probe can be replaced in one month. 2. If there are some performance problem, simply return it in its original condition within 30 days of receiving it. In the warranty period , we will repair it and sh you a good tester. 3. The warranty period will be extended for three months after we repair the bad product. 4. During the warranty period , freight AA system. 5. One year later, circuit fault free maintenance round-tr freight paid by buyer . 6. Please note that the guarantee policy does not apply to: A. Product has man-made damage or accidental damage such as exceive input voltage high temperature, water damage, drop and break, mechanical damage and corrosion. B. Unauthorized modification and tearing the product date mark.

EU Plug

US Plug package

Order descrtion

Shping: 1.We guarantee to sh goods out within 24-72 hour after payment confirmation except holiday. 2.We sh by China post,HKpost ,,,according to your choice when placing orders . 3.If you didn't receive the item after 45 days,please feel free to contact us.We will make all our effort to resoe the problem. 4.We are not responsible for delays causedby the customs, duties,taxes or other customscharges. Warranty: 1.All it have 1 year guarantee.IF your purchase do not meet merchantable quality, fitne for purpose or match the descrtion, We can make sure your iues are resoed . 2.For wrongly-shped it, Please contact us in 48 hours after delivery.We will arrange to deliver the correct it or return all your payment. 3.For defective or faulty products,please take photos or videos,we would resend or after confirmation.

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.