3D Printer Stepstick DRV8825 Driver Reprap 4 Layer

3D Printer Stepstick DRV8825 Driver Reprap 4 Layer

Descrition:

The module has an interface pinout is almost the same with A4988 motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications.

DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step).

It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling).

Feature:

Simple step and direction control interface

The interface can connect directly with 3.3V and 5V systems

over-temperature thermal shutdown, over-current shutdown and under-voltage lockout

short-to-ground and shorted-load protection

Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step

4-layer, 2 oz copper for improved heat dissipation

Adjustable current control you to set the maximum current output with a potentiometer, which lets you use voltages above your motor’s rated voltage to achieve higher step rates

Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)

45V maximum supply voltage

Built-in regulator (needed external logic voltage supply)

Note: This version has been soldered.

Package included:

1 x Stepstick DRV8825 driver





3D Printer Stepstick DRV8825 Driver Reprap 4 Layer



Descrition:



The module has an interface pinout is almost the same with A4988 motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications.

DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step).

It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling).



Feature:



Simple step and direction control interface

The interface can connect directly with 3.3V and 5V systems

over-temperature thermal shutdown, over-current shutdown and under-voltage lockout

short-to-ground and shorted-load protection

Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step

4-layer, 2 oz copper for improved heat dissipation

Adjustable current control you to set the maximum current output with a potentiometer, which lets you use voltages above your motor’s rated voltage to achieve higher step rates

Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)

45V maximum supply voltage

Built-in regulator (needed external logic voltage supply)



Note: This version has been soldered.



Package included:



1 x Stepstick DRV8825 driver
















a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a