9Pcs Car Panel Dent Repair Kit Paintless Dings Puller Remover Tool Kit

Specifications
:black+orange
Materials:metal+plastic
Voltage:100-240V
Frequency:50-60Hz
Function:repair car dents

Features
-Simple operation, quick recovery of dents directly for you.
-No paint sag repair, no damage to the paint, fast saving money and environmental protection.
-Three different sizes of traction gasket strips, suitable for various sizes of dents.
-Suitable for automotive sheet metal, refrigerator, washing machine surface sheet metal.
-Suitable for use where all kinds of flat metal are recessed.

Usage Method
1. Clean the dents with a clean, damp cloth;
2. Install the hot-melt bar from the back of the hot-melt , pull the trigger, let the bar enter the , plug in the supply, and let the preheat for 5 minutes;
3. Find a suitable traction gasket (a large traction gasket is needed for a large dent; (Note: the larger the traction gasket, the greater the traction force);
4. Pull the trigger of , and apply the extruded to the selected traction gasket (the 4 holes of gasket shall also be coated with hot melt
5. Quickly place the traction gasket coated with hot-melt adhesive in the center of the dent, press it gently until the hot-melt adhesive solidifies and sticks firmly; (let the hot-melt adhesive dry for about 8 minutes; we suggest that the hot-melt adhesive should not dry for more than 10 minutes.)
6. Align the hole in the middle of the traction tension axle with the fixed traction spacer bar, sleeve the screw rotation knob on the traction spacer bar, and slowly tighten it until the dent part is pulled to be flush with the surrounding surface
7. Some dents may need to be repaired by repeating the above steps several times.
8. If the repaired surface bulges a little, please follow the steps below: first, rub the convex starting point back and forth with the thumb until the convex starting point is as flat as surfaces; if the convex starting point cannot be restored to flat with the thumb, gently the convex starting point with the percussion bar (the gesture of holding the pen) until the convex starting point is restored to flat. Sometimes, it may need to be repeated several times. (Note: when using the percussion bar, do not use too much force.)
9. After the dent is repaired, screw down the screw rotating button, take down the traction tension bridge, and then take down the traction gasket. If there is hot melt adhesive stuck on the surface of the car body, let your hand gently tear it off.

Note
-Please allow a bit error due to manual measurement. please make sure you do not mind before you bid.
-The may have different as the difference display, please understand.

Package Included
1 x
3 x Traction Gasket Strip
1 x Traction Bridge
1 x Nut
1 x Bracket
1 x Stick
1 x Percussion Stick

a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a