KSGER T12 Station STM32 V3.1S DIY OLED Tools T12 Iron Ts ABS Case 907 Handle Auto-sleep

KSGER STM32 V3.1S T12 Station DIY OLED Tools T12 Iron Ts ABS Case 907 Handle Metal Stand Quick Heating

Note: We have changed the station ch to MM32 from 2021/12/1. But it will be same firmware and same function with STM32,so please donot worry about it. Only sets 7 and sets 8 include power plug,other sets has no power plug. NOTE: This station hasnot Hot air ! If U want change the default T , please tell us or leave a meage. NOTE:Iron t do not work continuously high temperature, high temperature work is easy to damage the t! Ordinary solder meltin is 183°C, lead-free solder meltin is 227°C, usually the welding temperature is 300-380°C, 380°C is the temperature of the p>

T12 t list

If you donot need default T12 ts,please choose other T12 types from below and make a note when order or contact us first.

907 plastic handle

Regarding the problem that the temperature displayed on the station is not accurate with the actual temperature: Please use the iron t temperature tester (please do not use a multimeter) to test the temperature. When the station is working at low temperature (le than 280 degrees), the temperature displayed on the station and the actual temperature of the iron t are only for reference , which is not accurate because They are affected by the surrounding environment. The surrounding environment will carry away heat, causing the iron t to lose some heat. If using a HB t thermometer, pls make sure the iron t is suspended at the center of the temperature sensing line. If you are very strict with temperature, please do not buy this station. The problem that tin wire cannot be melted at 227 degrees. The meltin is the meltin of the substance itself. When the temperature of the substance reaches the meltin of the substance, it is poible that the substance cannot be melted. For example, the meltin and freezin of ice are both 0 degrees Celsius, and water does not necearily freeze at 0 degrees Celsius. Since the temperature of the substance is affected by the surrounding environment, the actual meltin of the tin wire is higher than the meltin indicated by the tin wire. If the wire is placed in a thermostat tin furnace at 226 degrees Celsius, it is poible to melt in a sealed tin furnace. If it is wrapped around the iron t, it is impoible to melt. Because there is a gap between the tin wires, and the station has a temperature difference, the iron will lose some heat when it heats up, and the surrounding air will also absorb heat. The meltin of lead-free wire is 227 degrees Celsius, and the room temperature is low in winter. Under the premise of calibrating the temperature of the station, at least 50 degrees Celsius should be increased to offset the heat absorbed by the air, so that the heat of the wire itself can be increased to 228 degrees Celsius. About the wake of the handle Please carefully understand the working princle of the vibration switch in the handle. The ball trigger switch built in the handle, the mounting direction of the ball switch and the rolling direction of the ball inside the ball switch need to vibrate the handle when the direction of the handle is consistent. For example, when the handle is vertical Please move the handle up and down. When swinging the handle up and down, please make sure that the ball inside the handle can trigger the SW wake-up mode, and the force needs to be slightly larger. When the handle is placed horizontally, please swing the handle left and right. Please swing the handle to an angle greater than 30 degrees, so that the ball inside the handle can trigger the SW wake-up mode. About the station showing of ERROR If the ERROR is displayed, the handle or the t is not installed properly. Please use a pair of pliers to push the t into the innermost part of the handle. Then try rotating the t to ensure that the tab of the t is in good connect with the inner tab of the handle. If ERROR is still displayed and the light is always on when the t or handle is installed, please contact us to get a solution. We encourage buyers to communicate with us to soe any probl. We will do our best for each buyer.

Describe your brands story, including establishment and development timelines, milestones, etc.

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.