ZKPP1K Dual Mode LCD PWM Signaenerator 1Channel

P roduct D escription

1.PWM signaenerator, square wave rectangular wave signaenerator;

2.Used to generate a square wave rectangular wave signal, which is supplied to a DC motor or a stepper motor driver; Stepper motor, servo motor, electric gripper, robot arm;

3.Combine the driver to realize dimming, speed regulation, control solenoid valve, etc. However, it is not poible to directly drive loads such as electric lights, motors, and solenoid valves.

Highlights:

1. Two modes can be selected:

PWM mode - frequency (continuous), duty cycle.

Note that the number of pulses cannot be set in this mode, and the pulse is always emitted;

PULSE mode - positive pulse width time, negative pulse width time, delayed start time, and adjustable number of pulses.

2. With start-stop on, external switch can also be used to control output signal ON/OFF.

3. Wide voltage input 3.3-30V, with anti-reverse protection, 5.08mm terminal wiring.

Technical P arameters:

1. Working voltage: 3.3~30V, with anti-reverse protection ;

2. Frequency range: 1Hz~150KHz, accuracy about 1% ;

3. Duty cycle range: 0-100%, 1% stepping ;

4. Number of pulses: 1-9999, or infinite (display '----' stands for infinity) ;

5. Delay output time: 0.000s-9999s, the minimum can be set 1ms ;

6. Positive and negative pulse width length: 0.000s-9999s, the minimum can be set 1ms ;

7. Signal loading capacity: le than 30mA ;

8. Output signal amplitude: amplitude is equal to the supply voltage ;

9. Product size: 79mm*43mm*30mm ;

10. Product Weight: 40g ;

11. Packing: Anti-static bag.

Module D escription

1.on operation instructions

· There is an output waveform when power is turned on;

· Waveform amplitude = power supply voltage;

· The number of output pulses reaches the set value, the output is automatically stopped, and'oUT ' disappears;

· Pre the ON on to control the presence or absence of the waveform. OUT disappears to indi-cate no output waveform, and output o;

· Power-on reset or ON on to turn on the output, recalculate the number of pulses;

2.PWM mode (display has "%" for PWM mode)

The factory default mode is PWM mode, FREQ+ and FREQ-key set frequency, DUTY+ and DUTY-on set duty cycle; short pre ON on control signal output or stop, stop output is 0, the screen displays "OUT" mark as There is output, otherwise it stops output; the default factory frequency is 1KHZ and the duty cycle is 50%.

If you want to switch to PULSE mode, long pre the SET on (more than 6 seconds), do not release, you will see the screen change, "%" disappears, it is PULSE mode.

3.PULSE mode (No "%" on the right side of the display is PULSE mode)

The line above the LCD screen displays the positive pulse width time. The P+ and P- ons set the parameter. The line below the LCD screen displays the negative pulse width time. The N+ and N- ons set the parameter. Pre the ON on to control the signal output or stop. When the output is stopped, the output is 0. The screen displays "OUT" for output, otherwise it stops output; the default factory positive pulse width is 0.5 seconds and the negative pulse width is 0.5 seconds.

Pulse number and delay time setting - In PULSE mode, pre and hold the SET on for 2 seconds and then release, enter the pulse number and delay time setting interface, the screen displays SET, it will be turned off and cleared ar entering. ;P+ and P- ons set the delay time, N+ and N- ons set the number of pulses, the factory default delay time is 0 seconds, the number of pulses is infinite (display ----); then pre SET on 2 In seconds, it will automatically return to the pulse interface, pre the ON on, ar the delay setting time, start to iue the set number of pulses. If the number of pulses is sent, it will automatically output 0. If the period is not sent, preing the ON on will turn off. The output pulse is turned off and cleared, and the set number of pulses is iued each time it is started. Ar the number of pulses is sent, the display 'OUT' automatically disappears.

4 Application Operation Examples

① PWM output 20KHZ, 60% duty cycle: Select PWM mode, the frequency is set to 20.00, and the duty ratio is set to 060%.

② The output is turned on for 0.6 seconds and turned off for 0.2 seconds. Infinite loop: select PULSE mode,the positive pulse width is set to 0.600, the negative pulse width is set to 0.200, the delay time is set to 0.000, and the number of pulses is set to --- -.

③ Power on or pre the start on, delay 5 seconds, then the output is turned on for 0.6 seconds, off 0.2 seconds, infinite loop: select PULSE mode, positive pulse width is set to 0.600, negative pulse width is set to 0.200, delay The time is set to 5.000 and the number of pulses is set to ----.

④ Power on or pre the start on, delay 5 seconds, then output high level 10ms low level 10ms pulse 100: select PULSE mode, positive pulse width is set to 0.010, negative pulse width is set to 0.010, delay The time is set to 5.000 and the number of pulses is set to 0100.

⑤ Power-on delay for 10 seconds, then permanently output signal: select PULSE mode, the positive pulse width is set to a number greater than 0, thenegative pulse width is set to 0, the delay time is set to 10.00 seconds, and the pulse number is infinite. (----).

⑥ Other applications can explore or consult customer service.

All setup are not lost when they are turned off.

About shipping
Shipping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days ar buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.